Clutch slave size?

Mr Gazza · Yesterday, 07:10 PM

Please could anyone tell me the diameter of a standard clutch slave piston?
I'm after the size of the external type that bolts on the left side alternator cover.

I'm asking for a very good friend who is looking to make his wife's M600 clutch lever a lot lighter to help with her arthritis.
The 600 is an early one with the internal clutch side slave.
So being a very competent engineer, he is looking into boring the cylinder out and making another piston.
He did a series of experimental slaves for my Commando and they all worked well on a test rig, so he knows what he's doing.

If I knew what the standard size for the other side is I could compare that to the aftermarket ones to give him a guide size to aim for. Standard on the internal slaves is 26mm. I've got a feeling the external ones are too?

So far I have 29mm for Oberon and 27-27.5-28.5 and 30.5 for Elovuzione slaves.
If anyone knows what Factory Racing and others are it could be useful.

Thanks in advance.

Darren69 · Yesterday, 07:27 PM

There's a chart in this thread:
https://www.ducatiforum.co.uk/thread...iameter.75486/

Mr Gazza · Yesterday, 08:04 PM

Thank you Darren, that's absolutely perfect.

I found it on our very own forum a few minutes earlier and have already sent it to my mate.
It was originally compiled for Avanti Race Parts by Larry Shazaam Kelly apparently.
Name sounds familiar, but...

stopintime · Yesterday, 10:51 PM

Wet clutch on my 800 (maybe on that 600 too?) is the very standard 26 mm. I replaced it with a Yoyodyne 29 mm and that's just about what it can handle. Maybe 30 is ok too. I need the whole range of the lever to go from fully engaged to fully released (no drag).

Just a small real life observation.

Mr Gazza · Today, 08:50 AM

Thanks for the real life observation Lars, those are the most valuable and valid.

I'm also on a 29mm slave with 13mm master.
Interesting that you say your standard slave was 26mm.
The Avanti chart claims they are 25mm.
Unfortunately I no longer have a standard one to measure. Could anyone confirm the standard size of a bolt on left side slave please?

The internal one is definitely 26mm and it makes perfect sense that the two types would be the same to work with common masters.

Has anyone had any experience of boring out the clutch cover slaves?

Yesterday, 07:10 PM	#1
Mr Gazza Lord of the Rings Join Date: May 2013 Location: Norwich Bike: M900sie Posts: 5,964	Clutch slave size? Please could anyone tell me the diameter of a standard clutch slave piston? I'm after the size of the external type that bolts on the left side alternator cover. I'm asking for a very good friend who is looking to make his wife's M600 clutch lever a lot lighter to help with her arthritis. The 600 is an early one with the internal clutch side slave. So being a very competent engineer, he is looking into boring the cylinder out and making another piston. He did a series of experimental slaves for my Commando and they all worked well on a test rig, so he knows what he's doing. If I knew what the standard size for the other side is I could compare that to the aftermarket ones to give him a guide size to aim for. Standard on the internal slaves is 26mm. I've got a feeling the external ones are too? So far I have 29mm for Oberon and 27-27.5-28.5 and 30.5 for Elovuzione slaves. If anyone knows what Factory Racing and others are it could be useful. Thanks in advance. __________________

Yesterday, 07:27 PM	#2
Darren69 Transmaniacon MOC Join Date: Sep 2013 Location: Sutton In Ashfield Bike: Multiple Monsters Posts: 6,091	There's a chart in this thread: https://www.ducatiforum.co.uk/thread...iameter.75486/ __________________ Roast Beef Monster! Termignoni and Bucci - Italian for pipe and slippers! S4 Fogarty, S4R 07T, 748, Series 1 Mirage

Yesterday, 08:04 PM	#3
Mr Gazza Lord of the Rings Join Date: May 2013 Location: Norwich Bike: M900sie Posts: 5,964	Thank you Darren, that's absolutely perfect. I found it on our very own forum a few minutes earlier and have already sent it to my mate. It was originally compiled for Avanti Race Parts by Larry Shazaam Kelly apparently. Name sounds familiar, but... __________________

Today, 08:50 AM	#5
Mr Gazza Lord of the Rings Join Date: May 2013 Location: Norwich Bike: M900sie Posts: 5,964	Thanks for the real life observation Lars, those are the most valuable and valid. I'm also on a 29mm slave with 13mm master. Interesting that you say your standard slave was 26mm. The Avanti chart claims they are 25mm. Unfortunately I no longer have a standard one to measure. Could anyone confirm the standard size of a bolt on left side slave please? The internal one is definitely 26mm and it makes perfect sense that the two types would be the same to work with common masters. Has anyone had any experience of boring out the clutch cover slaves? __________________

Yesterday, 10:51 PM	#4
stopintime Registered User Join Date: Dec 2010 Location: Oslo Bike: S2r Posts: 448	Wet clutch on my 800 (maybe on that 600 too?) is the very standard 26 mm. I replaced it with a Yoyodyne 29 mm and that's just about what it can handle. Maybe 30 is ok too. I need the whole range of the lever to go from fully engaged to fully released (no drag). Just a small real life observation.