Register | FAQ | Members List | Calendar | Today's Posts | Search | Contact |
|
Registered
Members: 676 | Total Threads: 50,945 | Total Posts: 519,469 Currently Active Users: 1,126 (0 active members) Please welcome our newest member, Humph |
|
|
Thread Tools | Rating: | Display Modes |
06-04-2018, 03:10 PM | #106 |
Guest
Posts: n/a
|
Ok guys, back on it.
Started her up this week for the 1st time in 7 years!! Ran rough as Feck!! Oil pouring out of oil cooler/carb heater pipe junction (only tightened hand tight by some berk!!) and petrol pissing out of carb overflow pipes. 1st thoughts - carbs dry for 7 years = floats sticking Stripped down carbs again, checked and cleaned both floats and blew through everywhere with the airline. All seemed OK. Reassembled and fired it up but petrol still pouring out of both overflows. Any ideas? Where should I look next? Cheers |
06-04-2018, 05:51 PM | #107 |
Guest
Posts: n/a
|
Omg.... This is my nightmare.. I've just started stripping mine down...
I hope this goes well for you. I'll certainly be following this thread |
06-04-2018, 07:05 PM | #108 |
No turn left unstoned
Join Date: Jun 2010
Location: leicester
Bike: M750
Posts: 4,561
|
Well, my instinct says that if fuel is flowing from the floatbowl overflow pipe then the float valve has to be leaking, despite your previous cleaning.
The only other thing I can think of is that you have some pipes connected up wrongly and the fuel is actually flowing from somewhere else. Both seem unlikely but maybe not impossible. In the latter case, this could perhaps be compounded by a perished diaphragm in the fuel tap, causing it to remain open ... which would not be surprising after 7 yrs as rumour has it that they don't like drying out. All the above is a tad tenuous though. Does fuel flow from the overflow when the engine isn't running ? |
06-04-2018, 07:27 PM | #109 |
Transmaniacon MOC
Join Date: Sep 2013
Location: Sutton In Ashfield
Bike: Multiple Monsters
Posts: 6,095
|
Float heights incorrectly set or float valves not sealing? Check your cylinders aren't filling with fuel or it could all go bang, literally and in a fairly major way!
__________________
Roast Beef Monster! Termignoni and Bucci - Italian for pipe and slippers! S4 Fogarty, S4R 07T, 748, Series 1 Mirage |
07-04-2018, 01:04 AM | #110 |
Guest
Posts: n/a
|
Utopia - no fuel overflowing when engine not running - i will check fuel tap diaphragm.
Darren - checked and OK Am i right in thinking that the fuel is pumped to the carbs continuously when the engine is running? if so fault must be with floats/float height/float valve not shutting off incoming flow when carb bowls fill up. - Does that make sense? Will recheck all over the weekend - pilot error being my favourite bet for this!! |
28-04-2018, 10:38 AM | #111 |
Guest
Posts: n/a
|
Got it sussed.....
Some fool had connected the inlet from the fuel pump to the overflow on the back of the carbs........ It was me!!!! |
28-04-2018, 03:55 PM | #112 |
Pleasantly surprised!
Join Date: Nov 2016
Location: Stoke on Trent
Bike: M900ie
Posts: 780
|
The only reason I have not made the same mistake with mine is because I don't have carbs! Oh well it sounds like you are making progress!
__________________
Monsters don't hide under the bed, they sleep inside the shed |
29-11-2018, 10:47 PM | #113 |
Guest
Posts: n/a
|
OK back on the case - Cancer gone away (So far!!(Yahoo!!))
List of outstanding jobs:- 1. Make bracket to hold new mini speedo 1a. Organise new longer speedo drive cable 1b. Speedo drive - wheel end, what stop wheel end cable drive turning with the wheel other than the speedo drive cable? 2. Make new number plate holder v2 ( v1=sh*te) 2a. Probably water jet/laser cut to suit then powder coated 3. Sort out seat fixing 3a. order more fibre glass supplies 3b. get captive nuts welded to plate to glass into seat 4. Get seat upholstered (www.chaoscustom.co.uk) 5. New chain + sprockets (geared for wheelies!!) 6. Front indicators (thinking bar ends or wrap around top of forks LED) 7. Make brakes work after 7 years (splitting old Brembos........dodgy!!) 8. Make clutch work after 7 years 9. Make carbon fibre effect sprocket cover from naff grey plastic cover. 9. MOT Will be asking lots of silly questions to sort out all the above - thanks to all you Ducati Bros in advance for all the help I will pester you for. |
29-11-2018, 10:53 PM | #114 |
Anglo-Saxon Warrior
Join Date: Aug 2002
Location: North Yorkshire
Bike: M900
Posts: 2,485
|
Welcome back. Good luck with the on-going build.
Yorkie
__________________
NO ICE, GUN IT! |
29-11-2018, 11:03 PM | #115 |
Anglo-Saxon Warrior
Join Date: Aug 2002
Location: North Yorkshire
Bike: M900
Posts: 2,485
|
Bar end indicators on my SS cafe racer:
This sort of thing: https://www.demon-tweeks.com/bike-it...E&gclsrc=aw.ds Yorkie
__________________
NO ICE, GUN IT! |
29-11-2018, 11:05 PM | #116 |
Guest
Posts: n/a
|
Been out of touch for a while, what are you using to host pics now?
|
29-11-2018, 11:07 PM | #117 |
Guest
Posts: n/a
|
|
29-11-2018, 11:08 PM | #118 |
Guest
Posts: n/a
|
PS Yorkie
Nice arse!!! |
29-11-2018, 11:29 PM | #119 | |
Anglo-Saxon Warrior
Join Date: Aug 2002
Location: North Yorkshire
Bike: M900
Posts: 2,485
|
Quote:
For picture hosting I am using Flickr at the moment. Yorkie
__________________
NO ICE, GUN IT! |
|
29-11-2018, 11:32 PM | #120 |
Anglo-Saxon Warrior
Join Date: Aug 2002
Location: North Yorkshire
Bike: M900
Posts: 2,485
|
I take it you looked through the SS pictures? Only two ladies were pictured on the SS.
Yorkie
__________________
NO ICE, GUN IT! |
|
|