UK Monster Owners Club Forum » Gallery » UKMOC Bikes » My M750 Rebuild

Reply
 
Thread Tools Rating: Thread Rating: 11 votes, 5.00 average. Display Modes
Old 06-04-2018, 03:10 PM   #106
Taff666
Guest
 
Posts: n/a
Ok guys, back on it.

Started her up this week for the 1st time in 7 years!!
Ran rough as Feck!! Oil pouring out of oil cooler/carb heater pipe junction (only tightened hand tight by some berk!!) and petrol pissing out of carb overflow pipes.
1st thoughts - carbs dry for 7 years = floats sticking
Stripped down carbs again, checked and cleaned both floats and blew through everywhere with the airline. All seemed OK.
Reassembled and fired it up but petrol still pouring out of both overflows.

Any ideas? Where should I look next?

Cheers
  Reply With Quote
Old 06-04-2018, 05:51 PM   #107
davkyt
Guest
 
Posts: n/a
Omg.... This is my nightmare.. I've just started stripping mine down...
I hope this goes well for you.

I'll certainly be following this thread
  Reply With Quote
Old 06-04-2018, 07:05 PM   #108
utopia
No turn left unstoned
 
utopia's Avatar
 
Join Date: Jun 2010
Location: leicester
Bike: M750
Posts: 4,561
Well, my instinct says that if fuel is flowing from the floatbowl overflow pipe then the float valve has to be leaking, despite your previous cleaning.
The only other thing I can think of is that you have some pipes connected up wrongly and the fuel is actually flowing from somewhere else.
Both seem unlikely but maybe not impossible.
In the latter case, this could perhaps be compounded by a perished diaphragm in the fuel tap, causing it to remain open ... which would not be surprising after 7 yrs as rumour has it that they don't like drying out.

All the above is a tad tenuous though.
Does fuel flow from the overflow when the engine isn't running ?
utopia is offline   Reply With Quote
Old 06-04-2018, 07:27 PM   #109
Darren69
Transmaniacon MOC
 
Darren69's Avatar
 
Join Date: Sep 2013
Location: Sutton In Ashfield
Bike: Multiple Monsters
Posts: 6,095
Float heights incorrectly set or float valves not sealing? Check your cylinders aren't filling with fuel or it could all go bang, literally and in a fairly major way!
__________________
Roast Beef Monster!

Termignoni and Bucci - Italian for pipe and slippers!

S4 Fogarty, S4R 07T, 748, Series 1 Mirage
Darren69 is offline   Reply With Quote
Old 07-04-2018, 01:04 AM   #110
Taff666
Guest
 
Posts: n/a
Utopia - no fuel overflowing when engine not running - i will check fuel tap diaphragm.

Darren - checked and OK

Am i right in thinking that the fuel is pumped to the carbs continuously when the engine is running? if so fault must be with floats/float height/float valve not shutting off incoming flow when carb bowls fill up. - Does that make sense?

Will recheck all over the weekend - pilot error being my favourite bet for this!!
  Reply With Quote
Old 28-04-2018, 10:38 AM   #111
Taff666
Guest
 
Posts: n/a
Got it sussed.....

Some fool had connected the inlet from the fuel pump to the overflow on the back of the carbs........

It was me!!!!
  Reply With Quote
Old 28-04-2018, 03:55 PM   #112
Jez900ie
Pleasantly surprised!
 
Jez900ie's Avatar
 
Join Date: Nov 2016
Location: Stoke on Trent
Bike: M900ie
Posts: 780
Quote:
Originally Posted by Taff666 View Post
Got it sussed.....

Some fool had connected the inlet from the fuel pump to the overflow on the back of the carbs........

It was me!!!!
The only reason I have not made the same mistake with mine is because I don't have carbs! Oh well it sounds like you are making progress!
__________________
Monsters don't hide under the bed, they sleep inside the shed
Jez900ie is offline   Reply With Quote
Old 29-11-2018, 10:47 PM   #113
Taff666
Guest
 
Posts: n/a
OK back on the case - Cancer gone away (So far!!(Yahoo!!))

List of outstanding jobs:-

1. Make bracket to hold new mini speedo
1a. Organise new longer speedo drive cable
1b. Speedo drive - wheel end, what stop wheel end cable drive turning with the wheel other than the speedo drive cable?

2. Make new number plate holder v2 ( v1=sh*te)
2a. Probably water jet/laser cut to suit then powder coated

3. Sort out seat fixing
3a. order more fibre glass supplies
3b. get captive nuts welded to plate to glass into seat

4. Get seat upholstered (www.chaoscustom.co.uk)

5. New chain + sprockets (geared for wheelies!!)

6. Front indicators (thinking bar ends or wrap around top of forks LED)

7. Make brakes work after 7 years (splitting old Brembos........dodgy!!)

8. Make clutch work after 7 years

9. Make carbon fibre effect sprocket cover from naff grey plastic cover.

9. MOT

Will be asking lots of silly questions to sort out all the above - thanks to all you Ducati Bros in advance for all the help I will pester you for.
  Reply With Quote
Old 29-11-2018, 10:53 PM   #114
Yorkie
Anglo-Saxon Warrior
 
Yorkie's Avatar
 
Join Date: Aug 2002
Location: North Yorkshire
Bike: M900
Posts: 2,485
Cool

Welcome back. Good luck with the on-going build.

Yorkie
__________________
NO ICE, GUN IT!
Yorkie is offline   Reply With Quote
Old 29-11-2018, 11:03 PM   #115
Yorkie
Anglo-Saxon Warrior
 
Yorkie's Avatar
 
Join Date: Aug 2002
Location: North Yorkshire
Bike: M900
Posts: 2,485
Cool

Bar end indicators on my SS cafe racer:



This sort of thing:

https://www.demon-tweeks.com/bike-it...E&gclsrc=aw.ds

Yorkie
__________________
NO ICE, GUN IT!
Yorkie is offline   Reply With Quote
Old 29-11-2018, 11:05 PM   #116
Taff666
Guest
 
Posts: n/a
Been out of touch for a while, what are you using to host pics now?
  Reply With Quote
Old 29-11-2018, 11:07 PM   #117
Taff666
Guest
 
Posts: n/a
Yorkie

Front bar ends bro - more like this :-

https://www.moorespeedracing.co.uk/b...IaAj4jEALw_wcB
  Reply With Quote
Old 29-11-2018, 11:08 PM   #118
Taff666
Guest
 
Posts: n/a
PS Yorkie

Nice arse!!!
  Reply With Quote
Old 29-11-2018, 11:29 PM   #119
Yorkie
Anglo-Saxon Warrior
 
Yorkie's Avatar
 
Join Date: Aug 2002
Location: North Yorkshire
Bike: M900
Posts: 2,485
Cool

Quote:
Originally Posted by Taff666 View Post
Yorkie

Front bar ends bro - more like this :-

https://www.moorespeedracing.co.uk/b...IaAj4jEALw_wcB
Quality kit, I’m just a little bit tight (careful with money) and the SS was my first complete rebuild.

For picture hosting I am using Flickr at the moment.

Yorkie
__________________
NO ICE, GUN IT!
Yorkie is offline   Reply With Quote
Old 29-11-2018, 11:32 PM   #120
Yorkie
Anglo-Saxon Warrior
 
Yorkie's Avatar
 
Join Date: Aug 2002
Location: North Yorkshire
Bike: M900
Posts: 2,485
Cool

Quote:
Originally Posted by Taff666 View Post
PS Yorkie

Nice arse!!!
I take it you looked through the SS pictures? Only two ladies were pictured on the SS.

Yorkie
__________________
NO ICE, GUN IT!
Yorkie is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 09:14 PM.

vBulletin Skins by vBmode.com. Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.