UK Monster Owners Club Forum » Gallery » UKMOC Bikes » Back with a M900 series I

Reply
 
Thread Tools Rating: Thread Rating: 8 votes, 5.00 average. Display Modes
Old 21-06-2017, 10:20 PM   #346
Albie
Fanactical volunteer
 
Albie's Avatar
 
Join Date: Oct 2003
Location: Kent
Bike: M900
Posts: 9,034
These were redone too.

Albie is offline   Reply With Quote
Old 21-06-2017, 10:56 PM   #347
Dukedesmo
Registered User
 
Dukedesmo's Avatar
 
Join Date: Sep 2010
Location: Leics
Bike: M900
Posts: 2,901
Quote:
Originally Posted by Albie View Post
[/URL]
Looking good, only comment I would make is the rear cylinder oil return line looks a little short.

If you can get a slightly longer one so that it curves upwards a little more it will allow the cylinder jacket to completely fill with oil - too short and you may have a permanent air 'pocket' meaning the cylinder will run hotter?

If they're the only two you've got, I'd swap them over as the one on the front cylinder is longer and that will fill OK anyway due to the height of the return hole.
__________________
M900, 916, LeMans II.


Last edited by Dukedesmo; 21-06-2017 at 10:58 PM..
Dukedesmo is offline   Reply With Quote
Old 21-06-2017, 11:09 PM   #348
Darren69
Transmaniacon MOC
 
Darren69's Avatar
 
Join Date: Sep 2013
Location: Sutton In Ashfield
Bike: Multiple Monsters
Posts: 6,095
Yea, I'd say try swapping, front line too long and back a little short. I doubt it ever looked better though, Ducati wouldn't have taken so much time and care on finishing as you have.
__________________
Roast Beef Monster!

Termignoni and Bucci - Italian for pipe and slippers!

S4 Fogarty, S4R 07T, 748, Series 1 Mirage
Darren69 is offline   Reply With Quote
Old 21-06-2017, 11:43 PM   #349
Nasher
Registered User
 
Nasher's Avatar
 
Join Date: Jul 2014
Location: Portsmouth
Bike: M900
Posts: 1,518
Thanks Albie, worth knowing if I find a pair that are good enough to have a go at re-plating.

I don't have any at the moment.

Nasher
__________________
Heaven doesn't want me, and Hell is afraid I'll take over.
Nasher is offline   Reply With Quote
Old 21-06-2017, 11:49 PM   #350
Albie
Fanactical volunteer
 
Albie's Avatar
 
Join Date: Oct 2003
Location: Kent
Bike: M900
Posts: 9,034
Quote:
Originally Posted by Dukedesmo View Post
Looking good, only comment I would make is the rear cylinder oil return line looks a little short.

If you can get a slightly longer one so that it curves upwards a little more it will allow the cylinder jacket to completely fill with oil - too short and you may have a permanent air 'pocket' meaning the cylinder will run hotter?

If they're the only two you've got, I'd swap them over as the one on the front cylinder is longer and that will fill OK anyway due to the height of the return hole.
It's only a dry component run They are original and have natural bends but what you cannot see is the alternator cover is about 25mm away from casings. I may have them wrong way round but can check back as one has a plastic ring around pipe

Just checked and is correct way around here is old pic on buying day


Last edited by Albie; 22-06-2017 at 09:09 PM..
Albie is offline   Reply With Quote
Old 21-06-2017, 11:51 PM   #351
Dukedesmo
Registered User
 
Dukedesmo's Avatar
 
Join Date: Sep 2010
Location: Leics
Bike: M900
Posts: 2,901
Quote:
Originally Posted by Darren69 View Post
front line too long and back a little short.
I wonder if the short one isn't originally from a carb heater oil feed? as I think they use a short line between the float bowls?
__________________
M900, 916, LeMans II.

Dukedesmo is offline   Reply With Quote
Old 22-06-2017, 12:01 AM   #352
Albie
Fanactical volunteer
 
Albie's Avatar
 
Join Date: Oct 2003
Location: Kent
Bike: M900
Posts: 9,034
Quote:
Originally Posted by Dukedesmo View Post
I wonder if the short one isn't originally from a carb heater oil feed? as I think they use a short line between the float bowls?
No I have that one and has a 90 bend
It's all good and no need to panic
Albie is offline   Reply With Quote
Old 22-06-2017, 09:30 AM   #353
Darkness
.
 
Darkness's Avatar
 
Join Date: May 2007
Location: Stockbridge
Bike: M900
Posts: 1,984
Quote:
Originally Posted by Albie View Post

Sub assembly plated parts on sprocket hub carrier too starter motor fitted belt covers etc and painted oil cooler and drying curing nicely in this summer heat.

The sprocket is a good match for the original JT one: it's got nearly all of the holes. Are you going to give it a coat of satin black paint?
__________________
Original and Best since 1993
Darkness is offline   Reply With Quote
Old 22-06-2017, 09:56 AM   #354
Albie
Fanactical volunteer
 
Albie's Avatar
 
Join Date: Oct 2003
Location: Kent
Bike: M900
Posts: 9,034
Quote:
Originally Posted by Darkness View Post
The sprocket is a good match for the original JT one: it's got nearly all of the holes. Are you going to give it a coat of satin black paint?
No I like the colour and finish. Not going 100% anal. Don't want to ruin it
Albie is offline   Reply With Quote
Old 22-06-2017, 10:58 AM   #355
benson
Guest
 
Posts: n/a
Looking lovely Albie - well done!
  Reply With Quote
Old 22-06-2017, 09:05 PM   #356
Albie
Fanactical volunteer
 
Albie's Avatar
 
Join Date: Oct 2003
Location: Kent
Bike: M900
Posts: 9,034
Spent this evening putting new fork seals and bushes in the forks. Not the greatest of fun jobs but not within capabilities. Still got a spare set anyhow to mess around with.
So just have to get the oil tomorrow and fill them to correct level possibly + 10ml as advised.

They don't look so bad but they do have marks here and there but at least they have more gold colour.

That's all folks..




Albie is offline   Reply With Quote
Old 25-06-2017, 10:37 PM   #357
Albie
Fanactical volunteer
 
Albie's Avatar
 
Join Date: Oct 2003
Location: Kent
Bike: M900
Posts: 9,034
So finally have the front end loosely done complete other than the brake fluids and crush washers fitted to clutch and brake lines. Finally l figured out my brake line error and now fitted with correct length triple line with splitter.

I got the small paddock stand and rear from our MOB guy Sven and suits the bike lift just and was specific for Monster Showa I believe.

Sussed out the oil cooler lines and originally was correct with how I had it and had to put it back the way I did it. Now I need to find some more oil line banjos x 5 which have been awol it seems.
















Last edited by Albie; 25-06-2017 at 10:41 PM..
Albie is offline   Reply With Quote
Old 26-06-2017, 12:10 PM   #358
benson
Guest
 
Posts: n/a
That's looking good Albie - Shiny!!!
  Reply With Quote
Old 01-07-2017, 07:39 PM   #359
Darkness
.
 
Darkness's Avatar
 
Join Date: May 2007
Location: Stockbridge
Bike: M900
Posts: 1,984
Quote:
Originally Posted by Albie View Post
It's only a dry component run They are original and have natural bends but what you cannot see is the alternator cover is about 25mm away from casings. I may have them wrong way round but can check back as one has a plastic ring around pipe

Just checked and is correct way around here is old pic on buying day

Here's how they look on my '93:

__________________
Original and Best since 1993

Last edited by Darkness; 01-07-2017 at 08:23 PM..
Darkness is offline   Reply With Quote
Old 02-07-2017, 09:52 PM   #360
Albie
Fanactical volunteer
 
Albie's Avatar
 
Join Date: Oct 2003
Location: Kent
Bike: M900
Posts: 9,034
All my pics are gone thanks to Pooh Bucket but will check it out. My blog is now up to date after password got lost and Ladybird had to sort me one out as its a UKMOC email address she owns.

Mark thanks for backing up oil line saga and is the same as mine. Thanks also for email about clips that still needs looking at when other comes along next week.

Sorted out the breather pipes from carbs or maybe drain overflow pipes they may be. Had to get some more silicon tube this time 6mm dia and fits ok. If anyones looking though 5mm might be a nicer size and found this in a site that sells it for fishing lures as its sold in multi bright colours.
Fitted the 4 bearings SKF to the belt tensioners and the one same size to the clutch pressure plate.

Does anyone have a spare rear brake caliper retainer clip and pin as mine was shabby but was re plated and seems to be missing lately even though I know I saw it recently. No problem if not as available as spares.

Just the minor service stuff to order from Moto Rapido this week. Thinking I should order the bearings from the camshaft as were removed from heads even though they seem to be in good order and run nice along with the oil seal. Hardly seems worth the risk.
Albie is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 10:16 AM.

vBulletin Skins by vBmode.com. Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.