UK Monster Owners Club Forum » Gallery » UKMOC Bikes » Another m900 Rebuild gets started

Reply
 
Thread Tools Rate Thread Display Modes
Old 06-03-2017, 09:54 PM   #16
blackthorn
Guest
 
Posts: n/a
Keeping an eye in this! Good progress so far :-) I wanted to do mine this year but I'm heavily invested in doing my RS4 just now!
  Reply With Quote
Old 08-03-2017, 05:08 PM   #17
Albie
Fanactical volunteer
 
Albie's Avatar
 
Join Date: Oct 2003
Location: Kent
Bike: M900
Posts: 9,034
Hope this helps

Well today I feel I achieved something positive with the paint saga if and I say if in case and I always worry the sample original part sent to me by Darkness is the correct colour of the year. I believe it is and I got the part matched locally from an independent paint supplier who can custom mix rattle cans. We studied countless colour charts and was close with a Porsche one but we found a bike colour including ducati and cagiva and aprilia and got one very very close and he did a slight tint. He then took the sample suspension hoop and sprayed one side of a leg and it blended great. If you can notice it in the picture then well done. We also did part of the crap sample paint I did with Audi Dakota Grey so to check on that.
I am completely happy with it so I have 3 x 400ml cans to spray the frame over the powdercoat and have 2 cans of satin laquer.
It cost me £78 but I don't need a sprayer to do it.
If its successful and anyone decides they would be happy to get some please contact Kent Car Panel and Paint in Maidstone and they will be happy to make you some as they have all the details of the mix they did for me. Just say the custom 93 frame paint and its £12.95 +VAT per 400ml can.
Phone number is 01622 752821








Albie is offline   Reply With Quote
Old 20-03-2017, 08:19 PM   #18
Darkness
.
 
Darkness's Avatar
 
Join Date: May 2007
Location: Stockbridge
Bike: M900
Posts: 1,984
Slow progress: I picked up some nice fresh powder coated parts from Griff's in Bristol on Friday:

Footrest Hangers

Front Wheel

Lots of Lovely Elephants

Rear Wheels: I'll only use one at a time though........


From the comments about tyres on another thread here, I'm guessing that a date marking of 3805 and 1906 are getting a bit "Vintage" for road use, even if there's still half the tread left.

Still got to decide whether to repaint the frame?
__________________
Original and Best since 1993

Last edited by Darkness; 20-03-2017 at 08:21 PM..
Darkness is offline   Reply With Quote
Old 20-03-2017, 08:36 PM   #19
Mr Gazza
Lord of the Rings
 
Mr Gazza's Avatar
 
Join Date: May 2013
Location: Norwich
Bike: M900sie
Posts: 5,972
Hmmm..!

When you get your new tyres fitted tomorrow, get them to put some right angled valves in while they're at it.

__________________
Mr Gazza is offline   Reply With Quote
Old 20-03-2017, 08:55 PM   #20
Darkness
.
 
Darkness's Avatar
 
Join Date: May 2007
Location: Stockbridge
Bike: M900
Posts: 1,984
Quote:
Originally Posted by Mr Gazza View Post
Hmmm..!

When you get your new tyres fitted tomorrow, get them to put some right angled valves in while they're at it.
Tomorrow: why so urgent?

The wheels aren't even fitted to the bike yet, so all I need is something to protect the rims until it's assembled and MOT'd.

The right angle valves may be a good idea in case I ever have to use a forecourt pump, but my 12v Michelin pump has a very small head to the hose and works well with the standard ones?
__________________
Original and Best since 1993
Darkness is offline   Reply With Quote
Old 10-04-2017, 07:02 PM   #21
Darkness
.
 
Darkness's Avatar
 
Join Date: May 2007
Location: Stockbridge
Bike: M900
Posts: 1,984
Ooh err missus: it's got no clothes on........

It's cooled off again today, so back into the garage to take some more off the frame to get it ready for blasting, powder coat and paint [Thanks Albie].

There was a paper ticket on the loom, but it's not very informative! Must have got wet once too often.

All I need to do to it now is clean off the worst of the filth, and drill off the ZDM plate from under the side cover.

Next thing is to clean up the engine and start cleaning and renewing parts re the rebuild.

__________________
Original and Best since 1993

Last edited by Darkness; 13-07-2017 at 06:31 AM..
Darkness is offline   Reply With Quote
Old 10-04-2017, 07:28 PM   #22
Albie
Fanactical volunteer
 
Albie's Avatar
 
Join Date: Oct 2003
Location: Kent
Bike: M900
Posts: 9,034
Quote:
Originally Posted by Darkness View Post
It's cooled off again today, so back into the garage to take some more off the frame to get it ready for blasting, powder coat and paint [Thanks Albie].


There was a paper ticket on the loom, but it's not very informative! Must have got wet once too often.



All I need to do to it now is clean off the worst of the filth, and drill off the ZDM plate from under the side cover.



Next thing is to clean up the engine and start cleaning and renewing parts re the rebuild.

Are you going to powdercoat and paint. Is this to just protect it just wondered whether you should just prime or is he doing it a grey undercoat powder
Did they supply you paint ok
Albie is offline   Reply With Quote
Old 02-06-2017, 03:14 PM   #23
Darkness
.
 
Darkness's Avatar
 
Join Date: May 2007
Location: Stockbridge
Bike: M900
Posts: 1,984
Just had a message from Nick at Griff's: my frame has been blasted and primed so is ready for collection for the paint and lacquer to be applied.

That's prompted me to get on with sorting out which bits are going back on, and getting them cleaned.

I thought I had a choice of two swingarms, but closer inspection after cleaning them revealed a choice of one:

I'll be using this one.


Not this one.


Blobby blobby blobby!
__________________
Original and Best since 1993

Last edited by Darkness; 13-07-2017 at 06:25 AM..
Darkness is offline   Reply With Quote
Old 02-06-2017, 03:24 PM   #24
Darkness
.
 
Darkness's Avatar
 
Join Date: May 2007
Location: Stockbridge
Bike: M900
Posts: 1,984
Quote:
Originally Posted by Albie View Post
Are you going to powdercoat and paint. Is this to just protect it just wondered whether you should just prime or is he doing it a grey undercoat powder
Did they supply you paint ok
The frame is blast cleaned and primed.
I got 0.5l of colour coat and satin lacquer from Kent Car Panel to get the right colour.

Mine is:

That was matched with the original paint exposed where the TA tag was removed. Do you have the colour constituents of yours Albie? It would be interesting to know what difference there is [If any]?
__________________
Original and Best since 1993

Last edited by Darkness; 13-07-2017 at 06:26 AM..
Darkness is offline   Reply With Quote
Old 02-06-2017, 10:33 PM   #25
Albie
Fanactical volunteer
 
Albie's Avatar
 
Join Date: Oct 2003
Location: Kent
Bike: M900
Posts: 9,034
Quote:
Originally Posted by Darkness View Post
The frame is blast cleaned and primed.
I got 0.5l of colour coat and satin lacquer from Kent Car Panel to get the right colour.

Mine is:



That was matched with the original paint exposed where the TA tag was removed. Do you have the colour constituents of yours Albie? It would be interesting to know what difference there is [If any]?
Nope tbh. I thought at one point was looking at Aprilia colours or maybe a Porsche. I saw hundreds mate hundreds trying for an hour at least
Albie is offline   Reply With Quote
Old 04-06-2017, 10:07 AM   #26
Chriswilly
Registered User
 
Join Date: Sep 2012
Location: gloucester
Bike: M900ie
Posts: 133
Bought some frame paint from my local paint shop in Gloucester (Middleton Panels) and matched it by EYE!
Turned out to be 'perfect' - SILVER PEARL 2ct - Code 7-2-5748.00
Chriswilly is offline   Reply With Quote
Old 04-06-2017, 12:03 PM   #27
Darkness
.
 
Darkness's Avatar
 
Join Date: May 2007
Location: Stockbridge
Bike: M900
Posts: 1,984
Quote:
Originally Posted by Chriswilly View Post
Bought some frame paint from my local paint shop in Gloucester (Middleton Panels) and matched it by EYE!
Turned out to be 'perfect' - SILVER PEARL 2ct - Code 7-2-5748.00
If it's for your m900ie, the paint codes aren't such a problem for the post '98 bikes:
Quote:
Originally Posted by Stephenniall View Post


These are a few of the paint codes with PPG & Lechler codes. (Borrowed from another forum post.
Glad you got a match though as the colour now isn't necessarily the same as when it left the factory.
__________________
Original and Best since 1993
Darkness is offline   Reply With Quote
Old 26-06-2017, 09:19 PM   #28
Darkness
.
 
Darkness's Avatar
 
Join Date: May 2007
Location: Stockbridge
Bike: M900
Posts: 1,984
Should be getting the frame back later this week: let's hope it's a good match........

In preparation I've started bolting some sub-assemblies back together

Having watched Albie's rebuild progressing, I'm now not so sure about some of the fasteners and plates: what had seemed like patina now looks shabby, so I think I may now be getting some yellow passivated zinc plating done too?
__________________
Original and Best since 1993

Last edited by Darkness; 13-07-2017 at 06:27 AM..
Darkness is offline   Reply With Quote
Old 01-07-2017, 07:34 PM   #29
Darkness
.
 
Darkness's Avatar
 
Join Date: May 2007
Location: Stockbridge
Bike: M900
Posts: 1,984
I got the engine onto a stand this afternoon so I can work on it without breaking my back.
An old 80's Habitat trolley table retrieved from the loft provided the tubes.

I don't know who has the copyright for these, but it works well.

Oil is out now, and belt covers off. Time to start cleaning it up for some fresh paint.

I am finding a plethora of elephants on the bits, and date stamps.

The block casting is October '92 but the belt covers are Feb '93. There has been some work done on it though as the front [Horizontal] cylinder head is a '94 casting?

What do youse guys recommend for keeping ****e out of the engine whilst painting and the cam, rocker and generator clutch covers are removed? News paper and masking tape?
__________________
Original and Best since 1993

Last edited by Darkness; 13-07-2017 at 06:28 AM..
Darkness is offline   Reply With Quote
Old 05-07-2017, 07:24 PM   #30
Darkness
.
 
Darkness's Avatar
 
Join Date: May 2007
Location: Stockbridge
Bike: M900
Posts: 1,984
Picked up my frame today.

This has been blasted clean and powder coat primed by Nick at Griff's Reality Works and prep'ed, colour coated and lacquered by Del at DW. Automotive.

I'm pleased with the match, though it looks quite different without the rust and acid stains.

Del has also recently done the very nice Oxford livery for Staff's 888 racer.

http://www.ukmonster.co.uk/monster/s...ad.php?t=55411
__________________
Original and Best since 1993

Last edited by Darkness; 13-07-2017 at 06:28 AM..
Darkness is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 08:06 AM.

vBulletin Skins by vBmode.com. Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.