![]() |
Register | FAQ | Members List | Calendar | Today's Posts | Search | Contact | ![]() |
![]() |
|
![]() |
![]() |
Registered
Members: 673 | Total Threads: 50,931 | Total Posts: 519,351 Currently Active Users: 356 (0 active members) Please welcome our newest member, Mozzer46 |
![]() |
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
Join Date: May 2024
Location: Diss
Bike: M600
Posts: 32
|
AFR kit for a 1995 M600
Is anybody selling an air fuel ratio kit with sensor to fit a 1995 Monster 600 or can you suggest any recommendations of where I can buy one from ? I have found several on the market but not sure which one is suitable for my bike and a lot of them seem only suitable for cars.
|
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Dec 2014
Location: Aylsham
Bike: Multiple Monsters
Posts: 200
|
No experience of carbie Monsters but I'm sure that your's won't have an access point in the headers for a lambda probe so you could discount anything that uses one. Then I think you need to start ringing suppliers of what's left and ask if their product is suitable. Might be cheaper in the long run to book a dyno run with someone, they should include the data you want as part of the report. Why do you want one by the way?
Stop press - I was told today that the carbies DID have lambda ports in the headers - presumably for factory set-up?
__________________
NFN ![]() Last edited by dacs; 13-10-2024 at 05:58 PM.. Reason: correction |
![]() |
![]() |
![]() |
#3 | |
Registered User
Join Date: May 2024
Location: Diss
Bike: M600
Posts: 32
|
Quote:
|
|
![]() |
![]() |
![]() |
#4 |
Dismantled
Join Date: Feb 2006
Location: East Molesey
Bike: Multiple Monsters
Posts: 2,242
|
Why only suitable for cars ? AFR is the same on any engine whether its petrol, Deisel, LPG, Methol it matters not
Admitedly the cheap ones tend to be sold with a 52mm gauge which might lend itself to a car more easily however assuming all you want to do is measure as no way to adjust AFR when riding carby bike so probably better off with a decent probe style analyser, make sure it is wideband It won't be cheap - as all of the lower priced ones are just a narrowband controller with a gauge interface pretending to be wideband I would still question the need for such kit as can still only ever have it spot on for one condition on a carb motor which will change with atmospheric conditions and therefor be wrong 20 minutes later, however if like a few of us you just have to have a funky new tool --- this is the one I'd recomend as a starter It will do both probe and fixed lamda https://www.demon-tweeks.com/uk/inno...urvzY8LITfOsXF
__________________
"Political correctness is just intellectual colonialism and psychological fascism for the creation of thought crime" |
![]() |
![]() |
![]() |
#5 | |
Registered User
Join Date: May 2024
Location: Diss
Bike: M600
Posts: 32
|
Quote:
Thanks for the recommendation though, I will take a look. |
|
![]() |
![]() |
![]() |
#6 |
Dismantled
Join Date: Feb 2006
Location: East Molesey
Bike: Multiple Monsters
Posts: 2,242
|
Ah OK makes sense, the issue remains that the bung on your M600 was used for an O2 sensor what first run at the factory to check rich / lean and thats it !
You can get easily 1/8 BSP / NPT o2 sensors but they will not give you anywhere near the accuracy that an AFR sensor provides Most if not all wideband lambda's use M18 so roughly 10mm bigger than the hole you have !! so as said without welding your only simple option is a probe
__________________
"Political correctness is just intellectual colonialism and psychological fascism for the creation of thought crime" |
![]() |
![]() |
![]() |
|
|