Side stand for ducati monster 600 year 2000A

gallardo · 04-07-2024, 02:19 PM

Hi team,

Looking for a side estand for my beautiful m600. Anyone?

Gracias!

RichardDDuke · 04-07-2024, 03:56 PM

Have got a stand for a Ducati - it's from either a 90s' Monster or SS but not sure which model.
Can send photos if you want. I think I may have bought it off Mr. G but TBH I can't remember which stand I got from whom or where the others went.

It's been fitted with a modified part so that it doesn't flip up as soon as you stand the bike upright. It also has a 3 pin SuperSeal connector on the end of it as well.

Would like to get £50 + postage for it (probably around the £55 mark).

If you send me a PM with your email address in it then I can send you photos of the stand.

Mr Gazza · 04-07-2024, 07:14 PM

The side stand you got from me was from an M900ie. It has a forged steel mounting bracket and slightly kinked leg.
It will fit all the old shape Monsters, ST and SS too.
However the M600 will have had an Ally mounting bracket and possibly and ally leg too.
I'm sure this will be held by the two shoulder bolts that also hold the bottom of the footrest hangers whereas the steel one only picks up the forward shoulder bolt which leaves the need for a spacer behind the rear one.
The ally ones are usually the "suicide" type which ping up on their own once the weight comes off. The steel one has a switch (hence the cable and connector) which connects to n interlock killing the ignition when the stand is down.
There'll probably be no interlock circuit on the 600.

Dukedesmo · 04-07-2024, 07:24 PM

Quote:

Originally Posted by Mr Gazza

There'll probably be no interlock circuit on the 600.

Not an interlock but, I used an M600 (1999) wiring harness on my M900 and it has a connector to the stand for a stand-down indicator light.

Mr Gazza · 04-07-2024, 09:01 PM

Ah! Thanks Tim.
In that case the carbie and ie stand switches must work in the opposite sense to one another.

Carbie = Stand down. circuit closed to illuminate warning light
ie models = Stand up. circuit closed to enable engine to run.

I say this because in the absence of a switch, or a faulty switch on an ie model you have to use a jumper pin in the connector block to make the engine run and override the interlock.

You can swap between suicide or stay down stand by means of the link between spring and bracket.
Suicide link is straight and contacts the pivot bolt head before the spring is fully extended.
Stay down link is "C" shaped and wraps round the bolt head, clearing it.
I don't think the stay down link is a standard part, but they are still available as an after market part. I can find a web type link to the part if needed.

Dukedesmo · 05-07-2024, 08:35 AM

Coincidentally, the switch on my stand broke last week - the rubber moulding/cable relief basically broke off, bringing the wires with it.

I have since repaired it but did notice that although there are only 2 wires in the plug (circuit closed when down) there was also a third wire, albeit not connected to the plug, that was the opposite. Presumably to allow it's use on any variant?

As you say, stay down or 'suicide' options can be changed by the type of link/plate, my Monster has a stay-down stand whilst my 916 has the suicide version and has no switch fitted.

Darren69 · 05-07-2024, 01:45 PM

I have this for sale but dont know if it will fit a carby as it is for MIE and ST.
https://www.ebay.co.uk/itm/145747192...mis&media=COPY

gallardo · 10-10-2024, 09:50 AM

Sorry I have just only seen this. Do you still have the stand? Will it fit a carby m600 year 2000?

Quote:

Originally Posted by Darren69

I have this for sale but dont know if it will fit a carby as it is for MIE and ST.
https://www.ebay.co.uk/itm/145747192...mis&media=COPY

Darren69 · 11-10-2024, 09:49 PM

Quote:

Originally Posted by gallardo

Sorry I have just only seen this. Do you still have the stand? Will it fit a carby m600 year 2000?

No, sorry it was sold a while back.

04-07-2024, 02:19 PM	#1
gallardo Not Junior, Indiana.. Join Date: Apr 2004 Location: London Bike: M600 Posts: 101	Side stand for ducati monster 600 year 2000A Hi team, Looking for a side estand for my beautiful m600. Anyone? Gracias! __________________ Dale Don Dale!!

04-07-2024, 07:14 PM	#3
Mr Gazza Lord of the Rings Join Date: May 2013 Location: Norwich Bike: M900sie Posts: 5,961	The side stand you got from me was from an M900ie. It has a forged steel mounting bracket and slightly kinked leg. It will fit all the old shape Monsters, ST and SS too. However the M600 will have had an Ally mounting bracket and possibly and ally leg too. I'm sure this will be held by the two shoulder bolts that also hold the bottom of the footrest hangers whereas the steel one only picks up the forward shoulder bolt which leaves the need for a spacer behind the rear one. The ally ones are usually the "suicide" type which ping up on their own once the weight comes off. The steel one has a switch (hence the cable and connector) which connects to n interlock killing the ignition when the stand is down. There'll probably be no interlock circuit on the 600. __________________

04-07-2024, 09:01 PM	#5
Mr Gazza Lord of the Rings Join Date: May 2013 Location: Norwich Bike: M900sie Posts: 5,961	Ah! Thanks Tim. In that case the carbie and ie stand switches must work in the opposite sense to one another. Carbie = Stand down. circuit closed to illuminate warning light ie models = Stand up. circuit closed to enable engine to run. I say this because in the absence of a switch, or a faulty switch on an ie model you have to use a jumper pin in the connector block to make the engine run and override the interlock. You can swap between suicide or stay down stand by means of the link between spring and bracket. Suicide link is straight and contacts the pivot bolt head before the spring is fully extended. Stay down link is "C" shaped and wraps round the bolt head, clearing it. I don't think the stay down link is a standard part, but they are still available as an after market part. I can find a web type link to the part if needed. __________________

05-07-2024, 08:35 AM	#6
Dukedesmo Registered User Join Date: Sep 2010 Location: Leics Bike: M900 Posts: 2,894	Coincidentally, the switch on my stand broke last week - the rubber moulding/cable relief basically broke off, bringing the wires with it. I have since repaired it but did notice that although there are only 2 wires in the plug (circuit closed when down) there was also a third wire, albeit not connected to the plug, that was the opposite. Presumably to allow it's use on any variant? As you say, stay down or 'suicide' options can be changed by the type of link/plate, my Monster has a stay-down stand whilst my 916 has the suicide version and has no switch fitted. __________________ M900, 916, LeMans II.

05-07-2024, 01:45 PM	#7
Darren69 Transmaniacon MOC Join Date: Sep 2013 Location: Sutton In Ashfield Bike: Multiple Monsters Posts: 6,090	I have this for sale but dont know if it will fit a carby as it is for MIE and ST. https://www.ebay.co.uk/itm/145747192...mis&media=COPY __________________ Roast Beef Monster! Termignoni and Bucci - Italian for pipe and slippers! S4 Fogarty, S4R 07T, 748, Series 1 Mirage

04-07-2024, 03:56 PM	#2
RichardDDuke Registered User Join Date: Oct 2022 Location: Bedford Bike: Other Ducati Posts: 141	Have got a stand for a Ducati - it's from either a 90s' Monster or SS but not sure which model. Can send photos if you want. I think I may have bought it off Mr. G but TBH I can't remember which stand I got from whom or where the others went. It's been fitted with a modified part so that it doesn't flip up as soon as you stand the bike upright. It also has a 3 pin SuperSeal connector on the end of it as well. Would like to get £50 + postage for it (probably around the £55 mark). If you send me a PM with your email address in it then I can send you photos of the stand.