Good place to Powder Coat

Saint aka ML · 14-04-2015, 11:46 PM

Looking for a good and relatively cheap place that can remove current Powder coat from my rims and apply satin black instead.
Somewhere around London.

Any recommendations?

I will also need them to do same procedure on the frame when I have picked the colour plus few other bits and pieces.

15-04-2015, 06:44 AM

Chaps in Preston were tops, did my four foot rest hangers in less than a week and the finish was fantastic, I live in Devon and wouldn't go anywhere else

Kato · 15-04-2015, 07:27 AM

Armourtex Ltd
14-16 Rowe Lane
Hackney
London
E9 6EL

Phone: 0208 9862028

Email: armourtexltd@hotmail.co.uk

pompone · 15-04-2015, 08:50 AM

Armoutex won't do Aluminium anymore. Not even to trade.

damien666 · 15-04-2015, 10:11 AM

You'd have to post them, but www.triple-s.co.uk is the place my dad has used for years. Great reputation.

15-04-2015, 10:14 AM

Just a word of warning. General powder coaters bake the powder at around 200 degrees C.
There have been issues with cast Ali wheels cracking and distorting under load (do a google). So I only use a wheel specialist who slow bakes the wheel at a lower temperature, they then paint and lacquer over the top of that. I have just had my wheels back from Pristine Wheels in Woburn (Milton Keynes area) and they did a great job.
Any of the other parts that I had done were powder coated by a general finishing company.

slob · 15-04-2015, 10:35 AM

http://ukmonster.co.uk/monster/showt...ghlight=powder
check post #11

Dirty · 15-04-2015, 10:36 AM

Just a thought but could wheels be stripped and anodised rather than coated?

slob · 15-04-2015, 10:57 AM

you'd want to polish the hell out if them before anodizing to get a good finish

15-04-2015, 07:55 PM

Have a look at sudden impact motorcycles. They can do the complete job start to finish of differing components.

I've used them for several pieces of work.

DD

15-04-2015, 07:27 AM	#3
Kato Dismantled Join Date: Feb 2006 Location: East Molesey Bike: Multiple Monsters Posts: 2,247	Armourtex Ltd 14-16 Rowe Lane Hackney London E9 6EL Phone: 0208 9862028 Email: armourtexltd@hotmail.co.uk __________________ "Political correctness is just intellectual colonialism and psychological fascism for the creation of thought crime"

15-04-2015, 08:50 AM	#4
pompone MaleDucati Join Date: Jan 2009 Location: London Bike: M900 Posts: 817	Armoutex won't do Aluminium anymore. Not even to trade. __________________ www.desmoperformanceparts.com

15-04-2015, 10:36 AM	#8
Dirty Bockloks Join Date: Jan 2012 Location: London Bike: No Bike Yet! Posts: 4,601	Just a thought but could wheels be stripped and anodised rather than coated? __________________ Wounds heal, chicks dig scars, glory lasts forever Beware of eBay

14-04-2015, 11:46 PM	#1
Saint aka ML Junior ah to be young Join Date: Nov 2007 Location: London Bike: Multiple Monsters Posts: 2,058	Good place to Powder Coat Looking for a good and relatively cheap place that can remove current Powder coat from my rims and apply satin black instead. Somewhere around London. Any recommendations? I will also need them to do same procedure on the frame when I have picked the colour plus few other bits and pieces. __________________ "I am Lucazade"

15-04-2015, 06:44 AM	#2
bluestoesonnose Guest Posts: n/a	Chaps in Preston were tops, did my four foot rest hangers in less than a week and the finish was fantastic, I live in Devon and wouldn't go anywhere else

15-04-2015, 10:11 AM	#5
damien666 Registered User Join Date: Dec 2010 Location: Leeds, West-Yorks Bike: S4Rs Posts: 497	You'd have to post them, but www.triple-s.co.uk is the place my dad has used for years. Great reputation.

15-04-2015, 10:14 AM	#6
ibanezlynx Guest Posts: n/a	Just a word of warning. General powder coaters bake the powder at around 200 degrees C. There have been issues with cast Ali wheels cracking and distorting under load (do a google). So I only use a wheel specialist who slow bakes the wheel at a lower temperature, they then paint and lacquer over the top of that. I have just had my wheels back from Pristine Wheels in Woburn (Milton Keynes area) and they did a great job. Any of the other parts that I had done were powder coated by a general finishing company.

15-04-2015, 10:35 AM	#7
slob . Join Date: Jul 2003 Location: East London Bike: Multiple Monsters Posts: 9,737	http://ukmonster.co.uk/monster/showt...ghlight=powder check post #11

15-04-2015, 10:57 AM	#9
slob . Join Date: Jul 2003 Location: East London Bike: Multiple Monsters Posts: 9,737	you'd want to polish the hell out if them before anodizing to get a good finish

15-04-2015, 07:55 PM	#10
DangerousD Guest Posts: n/a	Have a look at sudden impact motorcycles. They can do the complete job start to finish of differing components. I've used them for several pieces of work. DD