UK Monster Owners Club Forum » Gallery » UKMOC Bikes » S4 Rebuild - so far

Reply
 
Thread Tools Rate Thread Display Modes
Old 25-03-2012, 06:37 PM   #1
littlejimmy12
Guest
 
Posts: n/a
S4 Rebuild - so far

The plan is to repaint the engine, frame and sundries and at the same time give her a bit of a service. I am a complete novice, I haven't used a manual, only luck and a camera! So far so good apart from swing arm pivot bolt. How the hell do you get that out?

First Mods 2 years ago


Stage 2 last year


And this year....the full monty


Tomorrow engine into the house

Last edited by littlejimmy12; 25-03-2012 at 06:51 PM..
  Reply With Quote
Old 25-03-2012, 07:03 PM   #2
Capo
You Are What You Is
 
Join Date: May 2005
Location: A Foward Location
Bike: S4r
Posts: 1,948
You sir are smitten the bike looks perfectly OK in the first two pics.

On the left side of the swing arm is a cotter bolt, the head is a 5mm allen and there is a nut on the other end. DO NOT try to rotate the bolt with an allen key. Remove the nut from the bottom and drift the bolt up and out, you should now be able to drift out the swing arm spindle (not sure if the DSS clamps on the right also), there may be shims if so make a note from where they came.
Once you get the swing arm off IMEDIATELY stuff a rag in each side of the case needle bearings. You do not want to know how hard it is to change these.
Have a look at the shaft for wear, about £35 for a new one.
Capo is offline   Reply With Quote
Old 25-03-2012, 07:48 PM   #3
littlejimmy12
Guest
 
Posts: n/a
Quote:
Originally Posted by Capo View Post
You sir are smitten the bike looks perfectly OK in the first two pics.
.
Thanks Capo. I am never happy! I have a vision of the bike and I won't be content until I get there! then again I'll probably finish and still have ideas!
  Reply With Quote
Old 25-03-2012, 10:29 PM   #4
pegboy
Guest
 
Posts: n/a
How loud is your bike with those pipes?? You should join the tunnel run, if you put it back together in time??
  Reply With Quote
Old 25-03-2012, 11:02 PM   #5
littlejimmy12
Guest
 
Posts: n/a
Quote:
Originally Posted by pegboy View Post
How loud is your bike with those pipes?? You should join the tunnel run, if you put it back together in time??
Its very very loud, it idles at around 100db. I do plan to join the tunnel run when its back together. My favourite game is to out rumble HDs
  Reply With Quote
Old 25-03-2012, 11:33 PM   #6
Capo
You Are What You Is
 
Join Date: May 2005
Location: A Foward Location
Bike: S4r
Posts: 1,948
Quote:
Originally Posted by littlejimmy12 View Post
Its very very loud, it idles at around 100db. I do plan to join the tunnel run when its back together. My favourite game is to out rumble HDs
By my reckoning, that gives you about 12 days, it can be done you know.
Capo is offline   Reply With Quote
Old 25-03-2012, 11:43 PM   #7
littlejimmy12
Guest
 
Posts: n/a
Quote:
Originally Posted by Capo View Post
By my reckoning, that gives you about 12 days, it can be done you know.
Won't be ready for a while, my budget is tiny so I have to wait for a few pay packets to afford the powder coating etc. I'm looking at 2 months until its finished. Plus I don't have electicity in my garage so I'm limited to weekend day work.

It will be worth it in the end
  Reply With Quote
Old 26-03-2012, 02:17 PM   #8
graham carroll
Guest
 
Posts: n/a
Great looking bike, were did you get the pipes also whats the sound like?
  Reply With Quote
Old 26-03-2012, 02:24 PM   #9
littlejimmy12
Guest
 
Posts: n/a
Quote:
Originally Posted by graham carroll View Post
Great looking bike, were did you get the pipes also whats the sound like?
thank you. The pipes were fabricated by Nick Gale Customs, they are next to The Ace just of the Hanger Lane roundabout. They are not one individual piece but several welded together. They labour costs made them v expensive.

You can still tell that my bike is a Ducati by the sound, but now it kind of has that Harley pupp pupp pupp sound on idle. To be honest I could do with some more baffling.

The idea was taken from Motocreations Boom Tubes which are made in the US.

J
  Reply With Quote
Old 26-03-2012, 06:12 PM   #10
littlejimmy12
Guest
 
Posts: n/a
Heeeeeeelp - swingarm removal

How do I do this





Capo whats a cotter bolt?
  Reply With Quote
Old 26-03-2012, 06:17 PM   #11
littlejimmy12
Guest
 
Posts: n/a
I have tried removing the pivot bolts and using my favourite tool, rubber mallet, knock the bolt through but its not budging. Rather than risk damage, please advise
  Reply With Quote
Old 26-03-2012, 06:43 PM   #12
Capo
You Are What You Is
 
Join Date: May 2005
Location: A Foward Location
Bike: S4r
Posts: 1,948
A cotter bolt has a tapered flat machined on it, the act of tightening the nut draws the taper onto the shaft thus securing it.
You need to give them a good clout with a hammer and a punch as you have to free the taper locking action. Don't worry too much about damaging the end of the bolt as they are cheap to replace.
Do not try to turn the bolt as the interface between the taper and shaft prevents rotation.

Once you have removed both cotters, the shaft can be driven out. However it is not unknown for the products of corrosion to seize them together, you best get a sturdy drift made up with a pilot so you can get some good wacks on it. Keep in mind that there are needle bearings and oil seals in the engine casing, damage them and you probably (given your financial situation) won't be riding it for a while.

Or you could take it to Rosso Corse I'm sure Ray would have it out in a jiffy.

Last edited by Capo; 26-03-2012 at 06:53 PM..
Capo is offline   Reply With Quote
Old 26-03-2012, 07:19 PM   #13
littlejimmy12
Guest
 
Posts: n/a
I think a trip to ray may be required here! I don't want to take any unnecessary risks a this point.
  Reply With Quote
Old 30-03-2012, 06:18 PM   #14
littlejimmy12
Guest
 
Posts: n/a
Quote:
Originally Posted by littlejimmy12 View Post
I think a trip to ray may be required here! I don't want to take any unnecessary risks a this point.
Proud to report my swing arm is now detached from the engine

Thanks to Slob for some good advice.
  Reply With Quote
Old 02-04-2012, 08:53 PM   #15
littlejimmy12
Guest
 
Posts: n/a
Frame off frame tube

Seal ring is off, how do I get the 'bearing inner race' and the rest of the stiff out the frame tube so I can slip my frame out!

last piece of the puzzle
  Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 12:34 PM.

vBulletin Skins by vBmode.com. Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.